Bristan Spare Parts
SPARE PARTS.
Bristan spare parts for showers, bathroom taps, kitchen taps and wastes, covering thermostatic cartridges, tap cartridges, valves, clicker waste mechanisms and cistern levers. Need help? Use our Bristan Identification Service by emailing a photo, and we will match you to the correct part.
Bristan Parts for Showers, Taps, Kitchen Mixers and Wastes
What we carry across the full Bristan range and how to find the right part.
Bristan is one of the most widely fitted tap and shower brands in UK bathrooms and kitchens. We carry Bristan spare parts across the full product range: tap cartridges and valves for bathroom and kitchen taps, thermostatic cartridges for shower valves, pop-up waste and clicker waste mechanisms, cistern levers and light pulls, shower hoses and handsets, and electronic control parts for sensor taps. Our stock covers both current production ranges and older discontinued models where Bristan parts are still manufactured. If you need a Bristan tap cartridge for an Easyfit kitchen mixer, a thermostatic cartridge for a Prism shower valve, or a replacement clicker waste for a basin, start with the relevant category below. Where you are not certain which part has failed or which model you have, use our identification service: email us a photo of the fitting with the part removed and we will match it to the correct Bristan spare.
Bristan Spares by Product Category
Each Bristan product type uses different internal components. This table covers what we stock and what typically needs replacing.
Bristan Identification Service
Not sure which Bristan spare part you need? Send us photos and we will identify the correct replacement.
Send photos. We identify. You order with confidence.
Prefer a quick start? Email now
What to send
One photo of the full item (tap, shower valve, waste fitting)
Close-up photos of any markings or model codes
Photo of the removed cartridge or valve from multiple angles
Basic measurements in mm (width, length, spline count if possible)
Short note describing the issue (dripping, running, temperature swings)
How it works
Step 1: Email photos and measurements
Step 2: We identify the closest match
Step 3: You order the correct spare part
Tip: Include a ruler in one photo so we can judge size accurately.
How to find your Bristan model code: check the valve body, the underside of the handle, the backplate, or the original care card and warranty paperwork. Bristan model codes typically start with a two or three letter prefix followed by a product descriptor.
Questions About Bristan Spare Parts
Common questions about finding and ordering Bristan spares.
Is there a Bristan spares catalogue I can download?
Bristan does not publish a single downloadable spares catalogue covering all models. The most reliable way to find your part is to identify your model code first, then check the relevant section on our site where each model has a parts breakdown with diagrams. If you have an older Bristan product and cannot find the model listed, email us a photo and we will check whether the parts are still available.
How do I know which Bristan tap cartridge I need?
Bristan uses several different cartridge types depending on the tap model and age. Single-lever mixer taps use a 40mm or 47mm ceramic disc cartridge. Traditional two-handle taps use quarter-turn valves, available in half-inch and three-quarter-inch stems. The safest approach is to remove the old cartridge first, measure the overall length and the diameter at the base, then match it against our Bristan tap cartridges and valves listings.
My Bristan tap is dripping. What part do I need?
A dripping Bristan tap is almost always caused by a worn ceramic disc cartridge or a failed seal. On single-lever mixers, replace the cartridge. On two-handle taps, replace the quarter-turn valve on the side that is dripping (hot or cold). If the drip is from the base of the spout rather than the outlet, the O-ring seals around the spout need replacing. Check the Bristan tap spares section for your model range.
Does Bristan still make spare parts for discontinued taps and showers?
Some discontinued Bristan parts are still manufactured because the same internal component is used across multiple models. A cartridge from a current range may fit an older tap or shower valve if the housing dimensions are the same. We stock parts for discontinued Bristan products where they remain available from Bristan or where a confirmed compatible replacement exists. If your model is no longer listed on the Bristan website, email us and we will check our stock.
What photos do I need for the Bristan Identification Service?
Send a clear photo of the full fitting (tap, shower valve or waste), a close-up of any markings or model codes visible on the body, a photo of the removed part you want to replace, and include a ruler or tape measure in at least one shot so we can gauge dimensions. Email these to sales@bathroomspareparts.co.uk and we will reply with the correct part number and a link to order it.
What our customers say