Clearwater Tap Spares
Official UK Supply Partner
CLEARWATER TAP
SPARE PARTS.
SPARE PARTS.
Explore Clearwater Tap Spares spare parts for a wide range of taps. If you are unsure which part you require, utilise our Clearwater Tap Spares Identification Service by sending us a photo, and we will assist you in identifying the correct part.
Technical Support Portal
Not sure? Email us a photo
★ Trusted UK stockist
★ 5 star Trustpilot rated
✓ Compatible spares supply
✓ Technical help by email
✓ Identify by photo
✓ UK-based support
Sort
Showing 4 of 4 Products
Clearwater Tap Spares
Showing products 1 to 4 of 4
£30.00 Inc. VAT
£25.00 ex. VAT
Clearwater 60mm Kitchen Waste Plug W60C
-150557-p.jpg?w=500&h=500&v=725F5E96-5A61-4979-9ED5-52EAC031AB9E)
£19.90 Inc. VAT
£16.58 ex. VAT
Clearwater Kitchen Tap Cold + Hot Valves 133.0358.055 + 133.0358.053
£20.00 Inc. VAT
£16.67 ex. VAT
Clearwater Miram Kitchen Tap Cold Valve 3984R COLD
£20.00 Inc. VAT
£16.67 ex. VAT
Clearwater Miram Kitchen Tap Hot Valve 3984R HOT
Clearwater Tap Spares Identification Service
If you cannot find a model code or part number, do not guess. Email us clear photos and we will help identify the correct Clearwater Tap Spares spare part for your taps, ensuring you receive the correct cartridge, valve, or seal without error.
Send photos. We identify. You order with confidence.
Prefer a quick start? Email now
What to send
1
One photo of the full tap
2
Close-up photos of any markings or codes
3
Photos of the removed cartridge or valve from multiple angles
4
Basic measurements in mm (width, length, spline count if possible)
5
Short note describing the issue (dripping, leaking, inconsistent flow)
How it works
Step 1: Email photos and measurements
Step 2: We identify the closest match
Step 3: You order the correct spare part
Step 2: We identify the closest match
Step 3: You order the correct spare part
Tip: Include a ruler in one photo so we can judge size accurately.
Model Identification Guide
Clearwater Tap Spares models may have codes or identifiers located on the body of the tap or underneath the lever. Refer to the following guide to understand where you should look.
| Infrastructure | Point of ID | Output |
|---|---|---|
| Monobloc Taps | Underneath the lever handle or spout | Model code or name |
| Wall-mounted Taps | Back of the tap body | Model code or reference |
| Deck-mounted Taps | Base of the tap or under cap | Model ID or serial |
| Bridge Taps | Crossbar or adjacent sides | Specific model identifier |
Common Spare Parts
The most frequently requested Clearwater Tap Spares include replacement cartridges, aerators, and seal kits. Identify what you need through our service for exact matches.
Common Faults and Fixes
Tap dripping
Caused by worn-out cartridges or seals. Identify and replace for proper functioning.
Weak water flow
Often due to blocked aerators or faulty cartridges. Inspect and clean or replace as necessary.
Leaking base
Caused by perished O-rings or gaskets. Replacement of the seal kit is advised.
Hard to operate handle
Due to worn internal components. Consider replacing the cartridge and handle.
Splashing water
Caused by a missing or blocked aerator. Check and replace if needed.
Inconsistent temperature
Usually due to a faulty thermostatic cartridge. Check and replace for steady temperature control.
Technical Support FAQ
How do I identify my Clearwater Tap model?+
Check under the lever handle or base of the tap for any identifying markers.
My Clearwater tap is making noise, what can I do?+
Noises can be due to aerator blockage or a worn-out cartridge. Cleaning or replacing these parts often resolves the problem.
What photos should I send for the Identification Service?+
Send a full tap photo, close ups of markings, photos of the removed part, and a measurement reference such as a ruler for scale.
How do I replace the aerator on my tap?+
Simply unscrew the aerator from the spout using your hand or a proper tool to avoid scratching. Replace with a new one ensuring a snug fit.
What if my Clearwater tap part has no code or markings?+
That is common on older models. Photos and dimensions allow us to identify the correct part.
Can you help if I only have the handle of the tap?+
Yes, but identification is faster if you can include a photo of the removed cartridge or internal valve along with any measurements you can take.
How to deal with minor leaks around the handle?+
Check for worn-out O-rings or seals. Replacing these often fixes the issue.